Light Weight Triggers, Heavy Rifles

This unique little part does some big things. The primary purpose being finite trigger control on large frame AR’s, hence the name, the FTC.

The FTC came about as a way to stabilize my shaky fingers. I had done something similar on a bolt rifle and it was so successful for me, decided to see if it would work on an AR. And it does, in spades.

1 Absolute trigger control on the pull and during reset

2 Prevention of bumpfire/finger bounce when using light triggers.

3 Improved feel of the trigger while wearing gloves

And it does all this without altering the lower receiver or trigger mechanism in any way.

Trigger Control

To say that it offers trigger control is an understatement. You not only have finite control on the pull but also have it on the reset. Absolute control, especially for long range use…..

Light Weight Pull, Heavy Rifles

The FTC completely stabilizes your trigger finger and by doing so it has the unique ability to allow for the use of extremely light triggers in a Large Frame AR. Which up to this point hasn’t been an option due to how the rifle reacts during recoil of larger calibers in this platform.

I recently installed a TriggerTech AR Diamond in a 308. This trigger works flawlessly and when paired with an FTC, is easily controlled when set at the minimum pull weight of 1.5lbs. Using a trigger with this low of a pull weight is pretty much unheard of in a large frame AR.

With the FTC fitted there is no tendency for the rifle to double up/bumpfire/finger bounce when fired offhand.

Gloves…

Another feature of the FTC is it’s ability to increase trigger feel while wearing gloves, something in complete opposition to what you might normally find when wearing them.

This feature will be appreciated by anyone who operates with gloves…. such as hunters, Law Enforcement and the Military.

Ergonomics

The shape of the FTC draws your finger down to the lowest part of the trigger, right where you have the best leverage and lightest feel to the trigger, no matter what weight pull you have.

You will also find that it alters how you interact with the reset cycle of your trigger. After you pull the trigger the geometry of things tends to keep your finger pulled…. I believe it is just this feature that prevents accidental bump firing.

So now instead of having to remember to pin the trigger down, you actually have to think about letting the trigger reset. Trigger reset is super clean and can be done as fast or as slow as you want.

The FTC is super simple and super effective.

Ambidextrous Use

You will also find it does not interfere should you find the need to shoot on your offside, switching back and forth during a string of fire works just fine.

And yes, it is fully compatible for use on the left side of the receiver for you guys that use the dark side….

Things to Consider…

The FTC was designed to assist with the use of very light triggers in large frame AR’s. It will fit just about any AR but the most benefit will be seen with larger calibers.

It was also designed to be used in conjunction with trigger upgrades, primarily with straight shoe triggers but also works on ones with mild curves.

Trigger Choice

Velocity Triggers work well and I just installed an adjustable TriggerTech trigger that can be set very light. Your chosen trigger must use jacking screws (set screws that help keep your trigger tight against the pins.) Timney and Rise Armament also use jack screws, plus I am sure there are other brands available.

You can not use a trigger that directly pivots on the trigger pins. Most drop in triggers use bushings and this is what you must use due to how the FTC mounts and interacts with drop in trigger assemblies.

Milspec type triggers are not an option as they just have too much curve to them and are set too far back in the lower to be used with the FTC. Nor does it make much sense to use a Milspec trigger as they are usually rough, gritty, too much creep and heavy, none of which the FTC will make up for.

Different models of the FTC may be forthcoming, just depends on demand.

Grip Options

Hand and grip size is extremely important for the FTC to work at it’s best. I have average size hands and this is what the FTC was designed around. So the grip set up I use may not fit your hands. Smaller and Extremely large hands may require a different hold on your grip and possibly changing out that grip. (I use Magpul Moe K2+ grips on small frame AR’s and an Ergo Tactical Deluxe on my large frame) Users with smaller hands would probably benefit by using a non beaver tail style grip.

I am currently working to determine just what grips work best for specific hand sizes.

Where your finger contacts the FTC is what makes this thing work so the fit of your hand is important. One size does not fit all. It’s all about the ergonomics of the grip, trigger and FTC as a whole.

Order Info and Questions

I am going to be selling these directly from the website so if you want one send me an email request

If you have questions please do not hesitate to ask them before you order…. email address – tonykonovaloff@hotmail.com

When paid and I have a shipping address I will get it sent in the mail. (Sorry no out of US sales at this point) Package will include one unpainted FTC and fasteners to attach it.